marlin-pavel/Marlin/pins_MEGATRONICS.h

131 lines
3.1 KiB
C
Raw Normal View History

2017-12-22 20:04:27 +01:00
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* MegaTronics pin assignments
*/
#ifndef __AVR_ATmega2560__
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
#endif
#define BOARD_NAME "Megatronics"
#define LARGE_FLASH true
//
// Limit Switches
//
#define X_MIN_PIN 41
#define X_MAX_PIN 37
#define Y_MIN_PIN 14
#define Y_MAX_PIN 15
#define Z_MIN_PIN 18
#define Z_MAX_PIN 19
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 19
#endif
//
// Steppers
//
#define X_STEP_PIN 26
#define X_DIR_PIN 28
#define X_ENABLE_PIN 24
#define Y_STEP_PIN 60 // A6
#define Y_DIR_PIN 61 // A7
#define Y_ENABLE_PIN 22
#define Z_STEP_PIN 54 // A0
#define Z_DIR_PIN 55 // A1
#define Z_ENABLE_PIN 56 // A2
#define E0_STEP_PIN 31
#define E0_DIR_PIN 32
#define E0_ENABLE_PIN 38
#define E1_STEP_PIN 34
#define E1_DIR_PIN 36
#define E1_ENABLE_PIN 30
//
// Temperature Sensors
//
#if TEMP_SENSOR_0 == -1
#define TEMP_0_PIN 8 // Analog Input
#else
#define TEMP_0_PIN 13 // Analog Input
#endif
#define TEMP_1_PIN 15 // Analog Input
#define TEMP_BED_PIN 14 // Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN 9
#define HEATER_1_PIN 8
#define HEATER_BED_PIN 10
#define FAN_PIN 7 // IO pin. Buffer needed
//
// Misc. Functions
//
#define SDSS 53
#define LED_PIN 13
#define PS_ON_PIN 12
#define CASE_LIGHT_PIN 2
//
// LCD / Controller
//
#define BEEPER_PIN 33
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 23
#define LCD_PINS_D5 25
#define LCD_PINS_D6 27
#define LCD_PINS_D7 29
// Buttons directly attached using AUX-2
#define BTN_EN1 59
#define BTN_EN2 64
#define BTN_ENC 43
#define SD_DETECT_PIN -1 // RAMPS doesn't use this
#endif // ULTRA_LCD && NEWPANEL
//
// M3/M4/M5 - Spindle/Laser Control
//
#define SPINDLE_LASER_PWM_PIN 3 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 4 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 11